Single-Leg Box Squat

Single-Leg Box Squat is a squat pattern that develops lower-body strength while the hips, knees, and ankles flex together.

Primary muscle

Upper Legs

Primary musclesQuadriceps, Gluteus maximus

Secondary musclesHip adductors, Hamstrings, Calves, Erector spinae

Equipment

Bodyweight

← Back to exercise database

Set up for Single-Leg Box Squat

Prepare the training area

Use a level, non-slip surface and clear enough room for the complete movement.
Place any required mat, bench, or stable hand support before taking the starting position.

Position yourself for Single-Leg Box Squat

Stand close enough to the box to sit back without reaching, balance on the working foot, and extend the other leg in front.
Before adding load, confirm that each knee can track with its toes while the heels and both sides of each forefoot remain planted. Keep the non-working side stable and compare both sides before choosing the working range.

Choose and verify the starting level

Choose the easiest Single-Leg Box Squat variation that preserves the required body line and full controlled range; use elevation, support, or assistance as needed.
Perform one slow rehearsal repetition and change the setup if the equipment shifts, the range causes pain, or the target position cannot be maintained.

How to perform Single-Leg Box Squat

Follow the sequence in order, paying attention to the starting position, movement path, and finish described in each step.

Establish the stance for Single-Leg Box Squat with the torso tall and the chosen load held securely; spread pressure across the heel and both sides of the forefoot.
Inhale and brace the trunk before the hips and knees begin to bend.
Bend the hips and knees together, allowing the knees to track in the same direction as the toes.
Descend only as far as the heels, trunk, and load remain balanced over the mid-foot.
Push the floor away and extend the hips and knees together to stand tall without leaning backward.

Common Single-Leg Box Squat mistakes

These are the form changes most likely to move work away from the target muscles or make the repetition harder to control.

Knees losing alignment

Keep each knee moving in the same direction as its toes instead of collapsing toward the midline.

Foot pressure shifting

Maintain the heel and both sides of the forefoot; shorten the range if the heels lift or balance rolls to the toes.

Chest and hips separating

Brace before descending and drive the hips and chest upward together rather than letting one shoot up first.

Forcing depth

Use the deepest range that preserves balance and trunk control instead of chasing depth after the pelvis or spine changes position.

When to modify or choose another exercise

Reduce the resistance, range, lever length, or balance demand if Single-Leg Box Squat cannot be completed without compensation.
Stop when the exercise produces sharp, catching, radiating, or increasing joint pain rather than the expected muscular effort.
Use a supported or unloaded version when foot pressure, balance, or trunk position cannot remain consistent; seek individualized guidance when pain persists after those changes.
Compare sides with the same starting load and range; a persistent or painful asymmetry should be assessed rather than trained around blindly.

Programming guide

How to use Single-Leg Box Squat in a training program

Use Single-Leg Box Squat early in a session focused on upper legs, or early in a full-body session, when it is a priority lift; place it later when it supports volume for another main movement.

Where it fits in a session

Use Single-Leg Box Squat early in a workout focused on upper legs, or early in a full-body workout, when strength or technical progress is the priority; place it later when it supplies secondary volume.

How often to use it

Use one to three times per week as part of training the relevant muscle groups at least twice weekly; the same exercise does not need to appear in every session.

Starting rep ranges by goal

Goal	Sets	Reps or time	Rest	Effort and execution
Technique	2–4	3–6 per side	90–180 sec	Light to moderate; 3–5 reps in reserve
Strength	2–4	3–6 per side	2–4 min	Heavy, usually 2–3 clean reps in reserve
Muscle growth	2–4	6–12 per side	90–180 sec	Usually 1–3 clean reps in reserve

How to progress it

Use double progression: reach the top of the repetition range across all sets with the same technique, then add the smallest practical load and return to the lower end.

Pairing and sequencing

Pair with an opposing or low-skill accessory when the second exercise does not reduce safety or performance.
Count working sets toward total weekly volume for every major muscle group that contributes substantially.

Coach's notes

For general strength, start with 2–3 working sets of 4–8 repetitions per side and rest 2–3 minutes between demanding sets.
For muscle growth, use a moderate load for 6–12 controlled repetitions and count the sets toward weekly volume for the trained muscles.
Progress repetitions within the chosen range before adding a small amount of load, and record load, reps, range, and effort.

Scale the movement